製品情報
条件: 新しい | タイプ: 蒸留装置 | 製品タイプ: 他 |
原産地: 中国(本土) | 銘柄: tsh |
包装
包装: 木製ケース |
仕様
1.バブルキャップトレイ; 2.高効率トレイ; 3.広範な使用; 4.製品は高品質5.servive最高の価格と優れた
Conventional bubble cap trays are well- proven in applications with following conditions:
( 1)アプリケーション: preferred in low gas/liquid loading conditions、 low leakage rates;
( 2)available in different sizes and shapes;
( 3) liquid tight design possible;
( 4) favorable for low liquid loads;
( 5) Large loading range for vapor load;
( 6)continuous liquid hold up;
these bubble cap trays manufactured by us find many applications in refinery and ga植物。 these bubble cap trays are widely used in these sectors due to their effectiveness
Over a broad range of flow conditions and low susceptibility to fouling。 we offer these
Bubble cap trays both in standard as well as customized configuration。 these bubble
Cap trays are manufactured using high grade standard mater。
gas- liquid contacting element for bubble cap tray is bubble cap。 it has round and
溝- shaped structure:
1. the gas- liquid contacting element for bubble cap tray is bubble cap、 which has
Round and groove- shaped structure forms。
2. the bubble cap is installed above the chimney、 and will not leak in conditions
Of proper installation and gas- liquid load、 so the bubble cap tray is featured by stable
Operation and great flexibility。
3. for structural reasons、 the liquid level on the tray is relatively high、 and
two- phase contact is of long time。 because of its high cost and complexity、
Most modern column designs favour the use of sieve or valve trays over
バブル- cap trays。 bubble- caps should only be used wher very low vapour rates
have to be handled、 or adequate residence time is necessary for separation and/or
Chemical reaction、 or in applications wher a positive liquid seal is essential at all flow rates。
4. therefore、 the pressure drop is high、 entrainment is increased、 and the fall in
The liquid level on the tray is relatively great、 etc。
categoryの材料
名 | クラスi( q235- a) | クラスii( 0cr18ni9) | |||||
呼び径( dn) | 80 | 100 | 150 | 80 | 100 | 150 | |
バブルキャップの外径d1・回; 壁の厚さs1 | 80・回; 2 | 100・回; 3 | 150・回; 3 | 80 | 100・回; 1.5 | 150・回; 1.5 | |
外径dのバブルキャップのトップ3 | — | — | 152 | — | — | 152 | |
煙突の外径をd2・回; 壁の厚さs2 | 57・回; 3.5 | 70・回; 4 | 108・回; 4 | 57・回; 2.75 | 70・回; 3 | 108・回; 4 | |
全体の高さh1 | 95 | 105 | 107 | 95 | 105 | 107 | |
煙突の高さh2 | 57 | 62 | 64 | 57 | 62 | 64 | |
バブルキャップの高さh3 | 65 | 75 | 73 | 65 | 75 | 73 | |
高さの頂上からのスロットにhバブルキャップ4 | 1 | 40 | 45 | — | 40 | 45 | — |
2 | 35 | 42 | — | 35 | 42 | — | |
3 | 30 | 38 | — | 30 | 38 | — | |
ブラケットからの高さの底にバブル帽広州5 | — | — | 45 | — | — | 45 | |
スロットの高さh | 1 | 20 | 25 | 35 | 20 | 25 | 35 |
2 | 25 | 28 | — | 25 | 28 | — | |
3 | 30 | 32 | — | 30 | 32 | — | |
スロットb1の高さ | 4 | 5 | r4/13.5 | 4 | 5 | r4/13.5 | |
nのスロットの数 | 30 | 32 | 28 | 30 | 32 | 28 | |
スロットのピッチf | 8.38 | 9.82 | 17.7 | 8.38 | 9.82 | 17.7 | |
煙突の直径を産んだd1 | 55 | 68 | 106 | 55 | 68 | 106 | |
正味面積の煙突f1,cm2 | 16.06 | 25.85 | 73.05 | 17.16 | 27.75 | 73.05 | |
旋回によるエリアf2,cm2 | 25.12 | 38.94 | 78.50 | 26.68 | 43.21 | 78.90 | |
円形領域f3,cm2 | 19.84 | 30.90 | 80.00 | 21.04 | 35.39 | 85.10 | |
f4,cm2 スロットの総面積f4,cm2 | 1 | 22.97 | 38.27 | 102.5 | 22.97 | 38.27 | 102.5 |
2 | 28.97 | 43.07 | — | 28.97 | 43.07 | — | |
3 | 34.97 | 49.97 | — | 34.97 | 49.97 | — | |
f2/f1 | 1.56 | 1.50 | 1.08 | 1.55 | 1.55 | 1.08 | |
f3/f1 | 1.22 | 1.19 | 1.10 | 1.21 | 1.26 | 1.17 | |
バブルキャップの質量、 キロ | 1 | 0.68 | 1.11 | 1.40 | 0.56 | 0.88 | 1.40 |
2 | 0.67 | 1.09 | — | 0.55 | 0.87 | — | |
3 | 0.66 | 1.08 | — | 0.54 | 0.86 | — |