製品情報
タイプの処理: 機械を強く引きなさい | 条件: 新しい | 製品タイプ: プラスチック管 |
原産地: 中国(本土) | 銘柄: xintian | 電圧: 380v |
力(W): 9キロワット | 重量: 25ookg | 証明: セリウム, iso |
仕様
長距離- 力オフ: 30000n長距離- スピードオフ: 0.06-1m/min総電力: パイプスコープ9キロワット: 110-630mm
1 structure
It is mainly used for towing pipes smoothly、 and it is mainly composed of 接合 fra-me、 変動し draught caterpillar、 driven device and 伝送 device。 uP- caterpillar presses upon the pipes by cylinder、 and can move 変動し in the direction of press; down- caterpillar can be adjusted by transmission device。 tHe rubber blocks used for clamp pipes are fixed on double chains、 they can prevent remotion。 yOu can choose the type ・ldquo;v” or ・ldquo;私” rubber block 応じて to the diameters of pipes、 which is more effective to clamp the driven devices。 私T is reliable to control from long distance by using frequency conversion motor。
2 Technical parameter
、Ir- compressing tieで- | r3 | Max towing speed | 1.2m/min |
、Ir pressure | 6バール | Min towing speed | 0.06m/min |
nUmber of caterpillars | 6 | lEngth of fra-me | 2700ミリメートル |
power | 7.5kw | Max towing force | 50000n |
mIn 直径 of pipes | 280ミリメートル | Max 直径 of pipes | 630ミリメートル |
3 Operation
Preparation
Adjust the position of haul- off to the center of extrusion line。 、Djust 4 heights and horse to the 高さ of extrusion。
fIrst insure the voltage is the same as the voltage marked on nameplate、 then connect the electricity。
cOnnect the windpipe tie-i n of the input pipe to the air source by using the ・ldquo;1/2” soft pipe、 the air pressure shall not below 6 bar。
tHere is an windpipe tie-i n 、 which is used for supple gas for cutter、 at the end of the output pipe。
Adjust The pressure to 2.5 bar by using the トリプル-Connecting unit at the front of the device。 yOu can keep on adjusting the pressure at operating、 but insure that the pressure should be as low as possible to preventing influencIng the working。
tHe weight of the up caterpillar may cause the over- pressure when towing thin- wall pipe、 adjust the button for adjusting pressure to get the suitable pressure。
tHe clamp force can be adjusted by using the pressure-解除方法Ing valve、 yOu can keep on adjusting at operating、 but insure that the force should be as low as possible to preventing influencIng the working。
Checking the function button
Check out whether the function button below
1 main switch of electrical キャビネット
2 stop button for caterpillar
3 starting button
4 rotation button for caterpillar
5 adjusting button for towing speed
6 falling of up caterpillar
7 arising of up caterpillar
8 falling of down caterpillar
9 arising of down caterpillar
10 選択的な switch on line
11 創発 stop button
ランニング
Turn on main switch
Press スケジュールされた button
Press rotation button for caterpillar
Press falling button for caterpillar when pipes come into haul- オフ
Adjust towing speed
Turn down the main electrical switch first、 then turn down the gas source
4 Maintain
、ttentions
cHeck and repair regularly as handbook
tUrn down the main switch and lock it dead before maintaining and repairing to preventing 勃
pRepare suitable tools
cLear the dust and lipiD of the machine before maintaining and repairing、 especially at the output and connection of power
私T is forbidden to use the 陳腐化した material
Pneumatic system
Filter the pressed gas by using the トリプル-コネクティング、 pneumatic unit to protecting gas valve and cylinder
cHeck the oil level regularly
sUpply enough oil- fog for gas circuit、 the grain of oil- fog is adjustable
bLow the filter net clearly by using pressed gas、 it is forbidden to use アセトン and impregnant of acetone
tHe water filter of the トリプル-コネクティング、 pneumatic unit is used for accumulating cooling water from pressed gas、 must clear the water in the filter( 警告: the water may damage the gas valve and cylinder)
lubricatイオン
(warning: good lubricatIon can prolong the use life of the machine、 it exceed the range of responsibility for damage which is caused by not lubricatEd well)
It is no need to lubricating for the inner of chainwheel and ball 心棒S for supporting department 、 because they are sealed。
lUbricate the screws of height- adjust horse with the 潤滑剤 of mo dioxide。
sPray the 潤滑剤 of sulfureted mo at the クリアランス of the inner and outer of the chainplate、 one time a week at least
rEplace the Compression resistance lubricant of the gear box first after 500 operating hours、 replace a 第二 time after 2000 operating hours、 then one time after 5000 operating hours。 re-
ブランド: shell hakoma w45 or w68、 mobile gear629、 aral tv548、 bpenergol。
lUbricate the 柱状 gear with the long use life lipid、 replace it after 2000 operating hours。 re- ブランド: shell tivela compo and a。
rEplace the lubricating lipid if it seep out from shaft- connecting unit。 re- ブランド: staburags nbv 12/300kp。
tHe life of chain is relevant to 潤滑 if you choose high 粘性た lubricating material、 do not let it seep to inner of chain。 私F you choose low viscid lubricant、 mineral oil、 machinery oil even gear box oil、 they must retain perfect 流動性 at whatever 状況.
uSe bush or fog- sprayer for adding lubricant、 if the speed of chain is no higher than 0.5m/min。
Maintain daily
Clear the water from the pneumatic、 triple- connecting unit every day
cHeck out whether there is damage in 外観 of machine
Maintain weekly
Clean the machine
Check whether all the screws and clamping devices are tight、 tweak them if they are loosen
Check out whether all the switches、 buttons、 jacks、 cables、 repair them if they are broken
Check out whether all the gas pipes and tie-i n are sealed or not
Check out the degree of 気密性 of each chain
Check out whether the rubber blocks are broken、 keep them clean
Clear the pneumatic triple- connecting unit and replace the refresh oil
Replacement of Inter1ink ages for caterpillar
There are not many differences to other chains、 個性記述 details you can see in the department picture
Turn on the haul- off slowly when replacing till it is easy to get the broken inter1ink age。